Old X-ray Table and Generator Be Used with a New Digital X-ray System?

Can My Old Universal Easymatic X-ray Table and Generator Be Used with a New Digital X-ray System?

Some of the Universal Easymatic systems look like this

Some veterinarians purchased their x-ray table and generator 25+ years ago and they still work perfectly!

Through care and good maintenance, they have been able to produce diagnostic images over the years using film.

For some veterinarians, 2017 is the year they would like to stop using chemicals and standard film.

However, they do not want to spend the 17k-25k on a new table and generator when their old system is producing excellent mas/kvp options for each case.

The good news is your existing system can work well with proper installation with your new digital x-ray equipment. For computed radiography or CR it is a simple calibration that will enable the old table and generator be ready for use the day of the installation.

This installation should be carried out by the installer on the day of installation and prior to the training session with the veterinary staff.

For direct radiography or DR, the plate may be wired into the foot switch as a prep switch. The old universal Easymatic x ray table and generator send out a 120-volt prep and expose signal.

A conversion box is brought by our onsite installers so that the cesium technology can convert the voltage down to a high of 5 volts and a low of 0 volts.

Another item that we include with our system is a new foot pedal switch. Often times the old switch can be worn out and the wiring loose.

A new foot pedal switch ensures a smooth transition from prep to exposure. In some instances, we also include a hand switch which can be mounted on the wall.

This secondary option is nice especially if the foot switch was to go out you always have another backup to take a high-quality digital x-ray.

You do not always need to buy a new table and generators to enjoy the speed, safety, and quality of digital x-rays.

Contact us today.

We can help you upgrade your system to digital.

Here is a video showing the conversion from film to digital using the old table and generator.

Buy Veterinary Digital X-ray Equipment with Confidence

How to Buy Veterinary Digital X-ray Equipment without Experiencing Buyer's Remorse

Have you ever bought something and regretted the purchase?

I think I have at one time or another. However, it’s one thing to regret ordering a cheeseburger and fries, but quite another when I regret buying a $50,000 car or truck.

When I make a big purchase, I want to feel good about my decision. I want to make sure that I made the right choice.

I want you to feel great about buying from me! I understand it is no small thing for a Veterinarian to spend $20,000 or $30,000 on digital x-ray equipment, and I want you to feel great about buying from us.

So, here is my “purchase without buyer's remorse” plan:

The 30-day satisfaction guarantee, or your money-back offer. When you make a digital x-ray system purchase, I will give you 30 days so that you feel comfortable and confident that you made the right choice.

And if you are not satisfied, return your digital x-ray equipment for a full refund.

Yes, that is correct! A FULL refund!!

I know that after the vet digital x-ray equipment is installed in your clinic, and once you learn how to use the software, you will be very happy with the results you get.

I can offer this guarantee because I am very confident with the quality of the digital x-ray equipment we sell, and I want you to be completely satisfied.

Here is the fine print:

• Equipment must be returned in original packaging.

• Equipment cannot be returned if damaged by the user during your 30 days.

• The buyer pays the cost of shipping/packing/insurance of all returned equipment.

• You must give us a reasonable chance to correct any dissatisfaction.

The main reason I am offering this “30-day satisfaction guarantee or your money back” is to give you peace of mind.

I understand I’m not as big as Idexx, Cuattro, or Sound-Eklin. Perhaps that makes you think twice about trying us out.

But I am confident that our equipment is as good, if not better, and now we have a “30-day satisfaction guarantee or your money back” - which the big boys do not offer!

The bottom line is simple:

• I am offering quality digital x-ray equipment for the veterinary industry at an amazing price, with a great warranty, and now a 30-day guarantee.

• I want to do the right thing, treat you with respect, and help you be successful in your veterinary practice.

Call or text me - Brad Haven, Jr. - 530-355-5886

Upgrade to Digital X-Ray with Your Existing Table/Generator

 Saying Goodbye to Chemicals and Dark Rooms: The Digital X-Ray Advantage

Advantages of upgrading to digital X-ray:

• Faster viewing of X-rays compared to film x-ray.

• Elimination of the need for a dark room, saving 20-30 minutes of processing time.

• Improved environmental conditions and staff health:

  • No more purchasing and handling of chemicals.

  • Elimination of film, storage, toxic chemical fumes, and odors.

• Convenient sharing of X-rays:

  • Sending x-rays to a radiologist via email or PACS.

  • Easy sharing of X-rays with customers through email.

• Enhanced customer service and interaction:

  • Digital technology allows for easier and more efficient viewing of each X-ray.

  • More time can be spent with customers, providing better service.
     

We had one location that had a table/generator which was over 15 years old, and we were able to upgrade to digital, still using his old table and generator.  

Money saved!

The Doctor upgraded to a DR system, and we saved him money by using his old table and generator.

We can do the same for you and it doesn't matter if you want a CR or DR digital x-ray system.

TESTIMONY

Here is what the Doctor had to say in an unsolicited email a few days after the installation...
 

“Image quality is superb! Far better than Sound x-ray we use to have at Bakersfield hospital. We took abdominal X-rays on a 70-pound dog and the x-rays came out great. Thank you! Let me know if anybody wants to visit and see the images...I will be more than happy to show them the images” — Dr. Singh - Family Pet Hospital - Vacaville, CA

Use your current table and generator and go digital - for a CR or a DR system.

Radiographs for CCL Injuries and TPLO Surgery

When it comes to cranial cruciate ligament (CCL) injuries in your patients, x-rays play a key role in your diagnosis, treatment, and follow-up.

So whether you’re the surgeon performing the procedure or a GP referring your patient to a specialist, having a good understanding of what to look for on your radiographic images can help you provide great patient care.

It all starts when the patient first comes in to see you…

The initial visit

More than likely, you’ll be seeing a middle-aged, medium or large breed dog who suddenly started limping on one of their hind limbs.

During the exam, you determine that the pain is in the stifle. Then, using sedation, you perform more thorough palpation, followed by radiographs.

Your detailed exam of the knee reveals some swelling and a positive drawer sign, and you take x-rays to confirm your suspicion of a CCL tear.

Considering this is one of the most common orthopedic injuries in dogs, you’re probably correct. However, occasionally there may be a surprise—such as a fracture near the stifle, or even an osteosarcoma lesion for older patients.

Radiographs will help you correctly diagnose and document the problem, and rule out concurrent conditions.

With a recent CCL injury, you might not see a lot of obvious evidence on your views—that’s because it can take more time for radiographic evidence of a CCL problem to show up.

However, you will likely see compression of the infrapatellar fat pad—which indicates joint effusion.

If the condition is chronic, you may notice arthritis and other signs of long-term inflammation.

Planning for a TPLO surgery

If your patient is a good candidate for surgery, then it’s time to discuss options with the owner. A tibial plateau leveling osteotomy is a good option for many otherwise-healthy dogs, but of course, the recommendation may vary for each individual pet.

Now’s the time when pre-op radiographs come in, by helping you to measure the tibial plateau angle and determine the saw blade size and position of the bone plate and screws.

The importance of post-op radiographs

After a surgery such as a TPLO, it’s important to document that everything went well—that all implants are in place, the tibial plateau has been repositioned as planned, and that there were no complications such as bone splintering.

This will be very reassuring to a worried pet parent, and will also be a valuable part of your medical record.

These post-op radiographs can also provide more information if a problem or complication comes up later, by using these initial images as a frame of reference for comparison.

Radiographs are useful if complications arise

More than likely, your patient is doing great. In that case, follow-up x-rays will help you confirm and document that the bone has healed as expected.

However, if they do run into any problems—such as an infection or a fracture—an additional set of radiographs can help you diagnose the issue and treat it ASAP. And follow-up rads will allow you to monitor the patient’s healing progress and their response to treatment.

Basically, radiographs give you an “inside view” throughout the whole process of diagnosing and treating a CCL injury, and are useful for common surgical options such as a TPLO.

Digital radiographs are especially helpful in terms of sensitivity for soft tissues such as a joint space, and also for providing rapid results within seconds.

But no matter which radiology equipment you choose, your X-ray images will provide valuable information for diagnosis and treatment of CCL—for happy patients and clients.

Disclaimer: This article is for general informational purposes only, and not intended as a guide to the medical treatment of any specific animal.

Written by: Dr. Tammy Powell, DVM

Vertebral Heart Score: How and Why to Calculate One

A vertebral heart score (VHS) is a measurement used to determine if a patient’s heart is enlarged.

The VHS can provide valuable insight to complete your clinical picture, especially at times when you hear a heart murmur, for a general pre-anesthetic check, or to look for cardiac changes on breeds that are predisposed. 

It’s a simple, non-invasive way to get more information and to monitor for changes over time.

How to calculate a vertebral heart score

1. Obtain a high-quality lateral thoracic radiograph. Be sure…

   • To collimate.

   • That the patient is straight and not twisted or at an angle.

   • That you can see enough detail, especially the thoracic vertebrae and the borders of the cardiac silhouette.

2. Make your first measurement along the longest axis of the cardiac silhouette, from the ventral border of the carina of the mainstem bronchus to the apex of the cardiac silhouette.

   • You don’t need to measure this in centimeters or inches—instead, just hold up a sheet of paper to your x-ray viewer and make a mark for your measurement, or use calipers. Or, with your digital x-ray system, use the VHS function to mark the measurement right on your screen.

3. Now, hold the measurement up to the vertebrae, starting with the cranial edge of T4—this is the 4th vertebra to have a rib connected. Count the number of vertebrae (including the vertebral body and the following disc space) that fall into the long axis measurement.

   • Measure to a decimal place of 0.1 (for example, let’s say your first measurement was 5.2 vertebrae).

4. Make your second measurement. This time, you’ll measure along the short axis, which is the widest part of the cardiac silhouette. It should be perpendicular (at a 90-degree angle) to your first measurement.

5. Repeat the process of transferring this measurement to the thoracic vertebrae, starting with the cranial edge of T4. For this example, let’s say your measurement was 4.5 vertebrae.

6. Add these two numbers together.

• In this example, your VHS would be 5.2 + 4.5 = 9.7 

How to interpret the results

For dogs, a normal vertebral heart score is less than 10.7 (with an average range of 8.5 to 10.5). For cats, an average VHS is 7.5 (with a range of 6.8 to 8.1).

Anything larger than that is considered abnormal.

Of course, this doesn’t tell you exactly what’s going on—you’ll need further information such as an echocardiogram to determine whether there is DCM, HCM, or some other issue causing the enlargement of the cardiac silhouette.

However, the VHS is a great screening tool to let you know to investigate further. And, if you have a patient who already has cardiac disease, a VHS can help you monitor their disease progression over time, and provide tangible information to a client who wants to know how their pet is doing on treatment.

Keep in mind that, as with any diagnostic tool, there is some individual variation. Some pets—especially certain breeds such as boxers—may fall outside the normal VHS range even if they’re completely healthy.

So, look at the overall clinical picture when assessing a patient. But with that in mind, a VHS is a quick, easy, valuable addition to your toolkit when it comes to evaluating and monitoring cardiac health.

Vetebral heart score tool video

Disclaimer: This article is for general informational purposes only, and not intended as a guide to the medical treatment of any specific animal.

Written by: Dr. Tammy Powell, DVM

How to X-Ray a Cat Safely Without Sedation or Anesthesia

If you’ve ever tried to radiograph a fractious cat without sedation or anesthesia, then you know what a difficult challenge it can be.

In addition to blurry, crooked, non-diagnostic images, maybe you or your team members received some scratches and scars to show for the experience.

So, it’s understandable you might not want to try that again—both for your safety and for the cat’s safety.

However, there are some situations where you may want to avoid sedation or anesthesia—or, if it can’t be avoided entirely, to use the lowest dose possible to get the results you need—during an x-ray study on a feline patient. For example…

• Cats with advanced heart disease or other conditions that could make sedatives and anesthetic drugs dangerous.

• Patients with kidney disease or other conditions that cause less predictable metabolism of anesthetic drugs—possibly resulting in a cat that’s excessively drowsy for a whole day, and an unhappy client.

• A patient who’s otherwise friendly and great to work with, just very wiggly for their x-ray shots. A few tweaks may make the experience more comfortable for them and make sedation unnecessary.

• Contrast studies such as a barium GI study, where the patient has to be awake to avoid aspiration of the barium.

Of course, sometimes sedation or anesthesia may be safer, decreasing the kitty’s stress and risk of injury.

Only you know what’s best, using your clinical judgment. However, if you do have a situation where it’s worthwhile to try the radiographs WITHOUT sedation or anesthesia, here are a few tips…

Tips to get diagnostic radiographs on an awake cat

• Practice feline-centered protocols from the beginning.

• Have team members use quiet voices throughout the clinic, especially near the x-ray room or area.

• Use pheromone products, including diffusers or spraying the products directly on towels your patient will be in contact with.

• Lock the door to the x-ray room or area if possible. That way, no one will walk in by surprise and cause your patient to suddenly look in the direction of a swinging door.

• Give the cat a place to hide between views and try to complete the views as quickly as possible. Less time is usually better when it comes to felines. Try a test view to confirm your settings, and then either use digital radiographs or if using film shoot all views at once and then develop them while the cat is resting comfortably in a kennel or carrier. 

• If the patient is just too stressed that day and it’s not an urgent matter, consider rescheduling. Sometimes starting fresh—having the kitty return first thing in the morning and completing the radiographs quickly—is better for you and the patient (and the client may feel better about it when they see the decreased stress level in their pet).

• Make the cat as comfortable as possible during radiographs. For example, use a trough for VD views—it’s a lot more comfortable for them than having their spine right up against the x-ray table.

• Remember the machine’s noise. Many cats are fine during positioning, but then panic, wriggle and squirm once they hear the whirring and “beep” that happen when you push the button to take the shot. To avoid this problem, try talking to the cat in soothing tones, or have another background noise such as a white noise machine or calm music. That way, the sudden noise from the machine won’t stand out so much compared to the other background noises.

Remember, making the whole experience less stressful for the cat can also make everything less stressful for you and your staff.

So if possible, making a little extra effort to accommodate a feline patient can help you get diagnostic views more quickly, with a better time for everyone.

Written by: Dr. Tammy Powell, DVM 

What Is an Over-Exposed X-Ray, and Why Does It Matter?

In the last blog post, we talked about under-exposed radiographs and how to get better results.

But, it’s important to remember that overcompensating too far in the other direction can give you a problem in the other extreme: that is, over-exposed images.

This is basically the opposite of an overly white or light radiograph. Instead, the image may appear “burnt out,” and overly dark or black, making it difficult to see all the information you need to make your diagnosis.

Over-exposed radiographs can make your life difficult because of the obliteration of normal anatomy

An over-exposure usually means the x-ray beam was too powerful, and that a larger percentage of x-rays passed through the patient’s tissues to reach the film or plate. So, rather than seeing information about the patient, you end up with a blackened image with not nearly enough detail. 

Some structures, such as small blood vessels in the thorax, might not be visible at all.

In other words, over-exposure could cause you to miss important lesions or interfere with your interpretation of normal anatomical structures.

Reasons why your radiographs might be over-exposed

Here are some possible culprits…

• An error in technique (kVp or mAs settings).

• A machine or equipment error.

• Using grid technique without a grid.

• Variations in screens.

• Too short of a distance between the x-ray source and the film or plate.

Also, scatter radiation can contribute to darkening an already over-exposed image.

What to do about over-exposed images

To decrease your radiograph procedure time and minimize x-ray exposure to patients and staff, it’s best to get your shots right the first time. But if your images are overexposed, try…

• Using a “hot light.” Sometimes, an overexposed radiograph can still be read by holding it up to an extra bright light known as a “hot light.” 

However, if that doesn’t work, you will probably need to retake the radiograph. Here are some tips for getting a better shot the next time…

• Adjust your settings. Typically, lighter images can be obtained by lowering the kVp or mAs.

• Check for errors in technique, such as using or not using a grid setting.

• Collimate. That way, you reduce the area of the primary beam and reduce scatter radiation, giving your image an overall better quality.

• Measure patients in the position they will be in during the shot. For example, when taking a lateral thorax view, the thorax may be thinner when the patient is laying on their side than it was when they were standing up. If that happens, your settings would probably be too high based on the measurement obtained from a standing patient.

Also, be sure to follow these general tips for producing good X-ray images…

• Use technique charts for a good starting point for exposure settings. A good technique chart will remove much of the guesswork. 

• Keep your equipment in good repair, including routine maintenance as necessary.

• Consider digital radiography, which can take film development out of the equation, and shorten the waiting time between views (allowing you to adjust settings prior to taking more shots).

• Use appropriate patient restraint to minimize artifacts from movement.

With practice, good quality equipment, and a few tips for adjusting your settings… Getting a properly exposed image doesn’t have to be hard!

And getting the right exposure will help you save time, avoid the headaches of struggling with poor-quality images, and get to your diagnoses faster.

Disclaimer: This article is for general informational purposes only, and not intended as a guide to the medical treatment of any specific animal.

Written by: Dr. Tammy Powell, DVM

What Is an Under-Exposed X-Ray, and Why Does It Matter?

When it comes to your x-ray images, there’s a fine balance between too much or too little exposure.

Of course, you’ll always want to use the lowest settings possible to get the image you need, to minimize x-ray exposure to both your patients and your staff. 

But, it’s possible to go too low on your exposure settings—and often that results in an under-exposed, possibly non-diagnostic, image.

Why should you care about an under-exposed x-ray image?

The short answer is because your images will look very light and might not show enough detail or contrast for you to make a diagnosis. An under-exposed radiographic image could mean…

• Increased “noise.” This can show up as cloudiness, mottled areas, or even stripes on the image. In the areas outside of the patient, that’s not necessarily a problem—but extra noise or grainy patterns overlying the area you’re looking at could create artifacts or obscure details.

• White or light radiographs that are difficult to read. An under-exposed radiograph means there was less penetration of the x-ray beam through the patient’s tissues. This results in an x-ray image that looks overly white or light compared to a properly exposed radiograph. That “whitewash” effect can make it more difficult to see certain lesions or abnormalities.

In other words, under-exposure could mean artifacts, non-diagnostic results, or other confusion when it comes to interpreting your films or digital images.

Reasons why your radiographs might be under-exposed

Here are some possible culprits…

• An error in technique (kVp or mAs settings).

• A machine or equipment error.

• Using grids with a non-grid technique.

• Having two films on the same cassette.

• Variations in screens.

• A long-distance between the x-ray source and the film or plate.

This isn’t an exhaustive list, but it represents good areas to explore for getting better images.

How to get it right the first time

Using the least amount of radiation necessary to get your images is a good practice. However, if your beam isn’t strong enough to produce a diagnostic image, then you’ll have to retake the shots, which produces more potential exposure to patients and staff. 

So, it’s best to get it right the first time. Try these tips…

• Use technique charts. Charts will give you a good starting point for exposure settings, and take out much of the guesswork. Usually, you’ll have to increase kVp or mAs to improve an underexposed image.

• Keep your equipment in good repair, including routine maintenance as necessary.

• Use appropriate patient restraint, whether physical or chemical. This can minimize movement artifact, as well as any changes to tissue density that could happen if a patient moves their body in a way that’s different from when you measured them.

• Consider using digital radiography. This will minimize wait times between views (allowing you to adjust settings prior to taking more shots). 

Digital radiography also prevents errors that come from the film development process. That’s not the same thing as under-exposure… But, taking film development out of the equation does give you one less thing to worry about and makes it faster to troubleshoot if you ever do come across problems with your images.

Have an overexposed radiograph? Check here for more information and tips.

Disclaimer: This article is for general informational purposes only, and not intended as a guide to the medical treatment of any specific animal.

Written by: Dr. Tammy Powell, DVM

How to Talk to Pet Owners about Radiographs

“Does he really need an x-ray? Can’t you just give him some medicine and see how he does?

“Why is this so expensive? You just want to make money while my cat is sick!”

As a veterinarian, you’ve probably heard all of this and more.

Of course, most clients want the best for their pets, and many will understand why you want to perform certain tests like radiographs. However, even the most loving of pet parents may show some hesitation or “sticker shock” when you present the estimate…

Often, this isn’t personal. Many pet owners just aren’t prepared for a sudden expense, even if they want to do the best for their furkids. Here are some tips that may help take the conversation in a more positive direction…

Stay calm during the initial reaction

If an owner’s initial response is similar to the examples listed above, try to ignore the knee-jerk reaction to defend yourself. Get comfortable with allowing a moment of uncomfortable silence.

Often, clients will try to fill the silence themselves and offer more of their thoughts and questions. But even if they don’t do this, a quiet moment may give everyone the chance to take a breath and start over, calmly.

Don’t pile onto an owner’s guilt

Of course, you’ll need to explain why the radiographs are important for your treatment decisions, and what dangers exist for the pet if radiographs are delayed. 

However, if a pet owner understands this and is just having trouble affording the x-rays, they’re probably already feeling guilty. This causes them to lash out.

In this case, having empathy during the conversation can really help. Think about your tone of voice, body language, and anything else that may help elicit a productive conversation.

If you make an owner feel understood and accepted, they’re likely to come back to you as soon as they CAN afford the tests, rather than seeking care elsewhere.

Bundle your radiographs when possible

Often, estimates are presented as “a la carte,” with different options presented by cost, line by line. 

While this may work well in some situations, the client may try to pick and choose, asking which items can be eliminated in order to decrease the cost of treatment.

Instead, try estimates that list a total cost, with radiographs included. Some situations where this may work well include:

• Dental procedures with dental rads.

• Senior wellness testing, with bloodwork and screening rads.

• A blocked cat, with x-ray views included as part of the treatment plan.

• For three-view thoracic radiographs, bundle them together rather than listing the individual “per view” charges separately.

Of course, you can still list each item of the treatment plan, so the client knows the value they are receiving. But, list it as a total cost, rather than an itemized estimate.

Explain the benefits and limitations of radiographs

Many pet owners nowadays, especially Millennials, want to be fully involved in their pet’s care—that’s part of the reason why so many owners seek answers from Dr. Google prior to coming for a vet visit.

Those clients will want to receive answers about their pet’s condition right away—so, let the client know that radiographs will help to provide the answers they’re looking for. And since radiographs are available the same day, they can get answers to their concerns very quickly.

On the flip side, also prepare an owner that a radiograph might show normal results. If the pet is feeling well, then the client gets peace of mind. If the pet is ill, further testing may be required—by preparing the owner for this possibility ahead of time, you can avoid upset reactions as much as possible.

Ask about their biggest concern

Even though you probably already know the biggest concerns and questions clients have about x-rays, it never hurts to ask an owner why they’re hesitant. They may appreciate you listening to them, and it saves you time so you can address their biggest concern.

Some examples you may encounter include:

• Finances. In this case, you can suggest third-party financing options, such as Care Credit.

• Fear for their pet’s comfort, or having to leave their pet at the hospital. Here, discuss the procedure. If sedation is used, explain how this can minimize pain. Or, if digital radiographs are used, explain how this allows the views to be done fast so the pet can go home sooner.

Show clients the value you offer, even after the x-rays are finished

Be sure to go over the results of the radiographs with your client. Try using a quiet exam room rather than the treatment area, so they won’t be distracted.

Give the client a brief “x-ray orientation,” so they know which end is toward the pet’s head and what is abdomen versus chest, etc. Then, explain your findings. 

Whenever possible, bring a normal x-ray for comparison, so clients can really see the difference with an abnormal finding.

If you have digital images, share a copy with the client that they can look at after the visit. Offer to let them record you talking about the findings. That way, when the client goes home and shares the findings with their partner or family, everyone is more likely to understand and be on board with your recommendations.

With a little planning of the whole x-ray experience from the client’s perspective, you can make things easier on them—while at the same time, increasing compliance and getting better care for the pets you see.

Written by: Dr. Tammy Powell, DVM

Identifying Trauma in X-Rays of Hit-By-Car Patients

It’s been a slow day, and you just got back from lunch. Your first-afternoon appointment is waiting, and you look through their chart, preparing to go into the room… 

All of a sudden, the clinic doors burst open. You hear a big commotion upfront…

You walk up to see what happened and discover a distraught pair of pet owners holding carrying their Border Collie, who’s just been hit by a car.

How to avoid further surprises…

Of course, as a veterinarian, you’re probably used to something like this happening from time to time—panicked pet parents arriving at your clinic with a dog or cat in need. And you’re probably well-prepared to triage and decide what to do next…

However, you’ll want to avoid unpleasant surprises down the line—liked missed diagnoses—by ensuring that you find and plan for unexpected injuries.

For example, maybe that Border Collie has an obviously broken leg and some nasty road rash.

You’ll address those injuries, but first, you’ll explain to the owners that there are other conditions you need to check if their fur kid has just been hit by a car—conditions that could be life-threatening.

What to look for on the x-rays

Your physical exam will help direct you on what to look for. For example, if you feel a painful joint with crepitus, or hear crackles or decreased lung sounds when you auscult the chest, those will be areas you want to explore with radiographs. 

But, even if the lungs sound fine and you don’t find any other obvious abnormalities, it’s always good to evaluate the thorax and abdomen radiographically.

Sometimes, x-rays will need to wait…

For example, if the pet is in critical condition, they need stabilization first. And, you’ll use your judgment on whether sedation is needed and safe, for clearer and more diagnostic x-ray images, as well as for relief from pain and stress.

Then, when you read the radiographs, it’s important to evaluate EVERYTHING on your set of x-ray images. 

The impact of being hit by a car can cause trauma to many different parts of the body all at once, including serious internal injuries.

Here are a few things to check for on your radiographs…

• Pulmonary contusions. A strong trauma to the thorax can cause dangerous bleeding in the lungs, often visible on radiographs as alveolar or interstitial opacities.

• A ruptured bladder and uroabdomen. Look for signs of fluid in the abdomen, especially if you notice bloody urine. Try to visualize the bladder.

• Internal bleeding or damaged organs. If an organ such as the spleen has been injured, you may notice a hemoabdomen (although radiographically, this would be difficult to distinguish from a uroabdomen). In the case of ruptured intestines, you may notice spots of free air in the abdominal cavity.

• Broken bones, including the ribs and vertebrae. Visually trace along the bones one-by-one to be sure no lesions are missed. 

• Dislocations, such as a dislocated hip. Also, check for tail-pull injuries, especially in cats who may get their tail caught under a car’s wheels.

• Diaphragmatic hernia. Look for evidence of intestines or other abdominal organs in the thorax.

• Air or fluid in the pleural space. Seen as gas opacity, or fluid opacity.

• Skull and jaw radiographs if needed—in case of suspected head trauma.

Of course, other abnormalities are possible, too. As you know, pets don’t always “read the book” and clinical practice can be full of surprises! If you’re unsure of something on the films or digital images, it may be good to recheck it down the line to be sure no problems are brewing internally.

The number of views you take will vary depending on the size of the pet.

For emergency situations such as this, it may be worth having digital radiographs, for faster results without waiting for films to develop.

Also, it’s important to take orthogonal views. That way, you get the full pictures and lesions are less likely to be missed.

Re-evaluate and repeat radiographs as needed

This will depend on what you see on the first set of images, in addition to how the pet is doing in real life. Use your best clinical judgment to determine if and when repeat radiographs are needed, and keep the pet under close observation.

If there’s any doubt, consider using contrast studies to obtain more information, too.

By developing a plan for radiographs—and remembering to check everything on the images—you’ll increase the chances of finding unexpected injuries and addressing them earlier. Or, in case the radiographs are normal, you may be able to give more peace of mind to the worried pet owners.

---

Disclaimer: This article is for general informational purposes only, and not intended as a guide to the medical treatment of any specific animal.

Written by: Dr. Tammy Powell, DVM

Your Warranty and Service Coverage for Veterinary X-Ray

Today, every veterinarian recognizes the importance of incorporating digital X-rays into their animal hospitals.

A considerable number of them plan to transition from traditional film and chemical X-rays to digital systems this year.

While the initial concern typically revolves around the cost of acquiring a digital X-ray system, it is equally crucial to inquire about the warranty and its coverage.

Here are some pertinent questions to ask the prospective vendor when considering the purchase of a veterinary digital X-ray system:

1. What is the duration of the hardware warranty for my veterinary digital X-ray plate?

2. How long does the software warranty for my veterinary digital X-ray software last?

3. For how long will I receive software upgrades for the X-ray system used in my animal hospital?

4. How long will my veterinarian technicians have access to tech support, enabling them to seek answers to any queries that may arise during the daily implementation of digital X-rays in my animal practice?

5. What are the costs associated with continued phone support, software upgrades, and technical assistance after the warranty period ends?

6. Which entity is responsible for providing software and technical support? Who developed and owns the software?

7. Does the warranty cover labor and shipping expenses, as needed?

8. In the event that my X-ray plate requires repair, will a temporary replacement plate be provided?

It is common for vendors operating in the animal health sector to offer a minimum of a 1-year warranty.

Not all vendors possess ownership of the software that operates their veterinary digital X-ray plate, which holds significant importance. While a digital X-ray plate can remain functional for many years, the software it relies on may become outdated within a short span of time.

An example of this can be observed with Windows XP platforms. Unless companies continually update their software, it becomes incompatible with new computing platforms.

When veterinarians transition from computed radiography (CR) to direct radiography (DR), the predominant issue they encounter is not the failure of the CR system itself but rather the poor performance or lack of support for the software.

This issue is not limited to small companies alone. Renowned brands like Idexx and Sound have discontinued support for their older product lines by ceasing software upgrades.

Our aim is to offer you transparent service and support. Our animal health software has been developed in-house by JPI which has been manufacturing x-ray equipment, writing software, and providing telephone support for these products since 1994.

Here are the responses to the eight frequently asked questions:

1. What is the duration of the hardware warranty for my veterinary digital x-ray plate?

- The hardware warranty lasts for 5 years.

2. How long is the software warranty for my veterinary digital x-ray software?

- The software warranty is also valid for 5 years.

3. For how long will I receive software upgrades for my x-ray system to be used in my animal hospital?

- You will receive software upgrades for 5 years.

4. How long can my veterinarian technicians receive phone support for any questions they may have regarding the daily implementation of digital X-rays in my animal practice?

- Our tech support helpline will be available for your veterinarian technicians for 5 years.

5. What is the cost of continued phone support and software upgrades after the warranty period?

- The cost for continued phone support and software upgrades after the warranty period is $750.00 per year.

6. Who provides the software and tech support? Who developed and owns the software?

- Our Examvue Veterinary software is developed, supported, and owned by JPI. They have been offering industry support since 1994. For technical support, please call 516-513-1330, and select option 2. Our support team is based in New York.

7. Are labor and shipping costs covered under the warranty if needed?

- Yes, labor and shipping costs are included in the warranty as required.

8. Will a loaner plate be provided in case my X-ray plate needs repair?

- Yes, we will provide a loaner plate in the event that your X-ray plate requires repair.

Is the New Digital X-ray System Compatible with Innovet?

Many veterinarians invested in X-ray systems in the ’90s. Most purchased an Innovet Summit table and generator.

They used the table and generator along with cassettes enclosing film to capture X-rays and provide life-saving next steps for their pet patients.

Processing the film in the chemical rinse and developing the images in the darkroom enabled the practicing veterinarian to review the X-ray.

If the X-ray proved complicating or just interesting then the veterinarian would mail the X-ray to a specialist for a review or save the X-ray case for the next ‘radiology rounds’ in upcoming weeks and months.

During these radiology rounds, X-ray cases would be reviewed amongst veterinarian piers and sometimes even veterinary radiologist.

Even if the patient was deceased by the time of the review huge advances in pet medicine were and still are to this day applied.

If you're reading this you use to film with your old X-ray generator and table. You want to impact the neighborhood and village who depend on precise and timely diagnosis to treat their pets.

Digital X-rays can speed up the process not only of image acquisition but also provide clear diagnostic radiology rounds.

Most old tables and generators still can produce excellent X-rays.

Often times these old systems have new light bulb collimators and replaced fuses that enable the old workhorse to continue to provide the power for an X-ray.

Yes, you can use your old table and generator with two types of digital X-rays.

The first is computed radiography or CR which will work today with any generator as the image is captured on an erasable film cassette then scanned into the software where the digital image can now be interrupted, adjusted or emailed to pet owners.

The next is an AED cesium plate. Automatic exposure detection.

This allows the plate to prepare itself for the exposure to capture the image and send in second the inmate to the display monitor.

This is the newest way to capture X-rays.

Not having to wire the old X-ray system to the new digital X-ray system is a confinement advantage.

It removes an element of future failure in hardware by eliminating the interference box!

We can help answer more questions surrounding your old X-ray table and generator.

Reach out today and we would be happy to help.